Multiblitz Profilux plus 200 Ws Guide de l'utilisateur télécharger pdf (Page 9)

PROFILUX PLUS

QUICK START

1. Protection Cap

In order to open the reﬂector lock (red slider, located at the bottom of

the device) push the slider away from the protection cap. Remove the

protection cap by turning it counter- clockwise and pulling it away from

the device.

2. Halogen tube

Place the supplied halogen tube into the halogen tube socket by pushing

it down and then turning it clockwise. Keep in mind to avoid touching the

bulb with your ﬁngers to ensure longevity of the tube. Attach the supplied

pyrex dome (Code: PLUSKLA) when operating the unit with 110-130 V

mains voltage or a Propac battery pack.

3. Mains connection

Connect the unit to a power outlet using the supplied mains cable,

the „I-0“ button glows red and the unit is in „stand-by” mode. Switch

on the unit by pressing the „I-0“ button, the button lights up red and

the unit is ready for operation.

4. Synchronisation with a radio trigger

The unit/s may be ﬁred using a radio trigger (RS 2/ TRIGGER HAPPY/

TRIGGER ONE, sold separately). The radio trigger (transmitter) has to

be attached to the cameras’ ﬂash shoe, when the camera is triggered the

unit/s will ﬁre synchronously.

For detailed information on the RS 2/ TRIGGER HAPPY/ TRIGGER ONE

radio trigger please refer to the corresponding user manual.

Selecting the receiving channel:

The unit is equipped with a 16-channel radio trigger (receiver).

Transmitter (RS 2/ TRIGGER HAPPY/ TRIGGER ONE) and receiver must

be set to the same channel. The receiver can be activated and set to the

desired receiving channel with the following key sequences:

- Press and hold the “TEST” button , the unit ﬁres once and the symbol

for the channel selection “CH” appears on the display after 3 sec.

Now let go of the button.

- After approx. 2 sec. the unit emits a beep and the symbol on the display

changes from „CH” to „--“, meaning that the receiver is not activated

and no channel is selected (factory setting).

- The desired receiving channel can now be set by turning the output

control, e.g. to “12“ (channel 12). Conﬁrm the selection of the channel

by pressing the “Test“ button, the previously selected output appears on

the display again.

- The radio trigger is now active and acts on the selected channel.

- A total of 16 channels are available.

Changing the receiving channel:

- Press and hold the “TEST” button, the unit ﬁres once and the symbol for

the channel selection “CH” appears on the display after 3 sec. Now let

go of the button.

- After approx. 2 sec. the unit emits a beep and the symbol on the display

changes from „CH” to the previously selected channel, e.g. to “07“

(channel 7). The desired receiving channel can now be set by turning the

output control, e.g. to “15“ (channel 15). Conﬁrm the selection of the

channel by pressing the “TEST“ button, the previously selected output

reappears on the display.

- The radio trigger now acts on the newly selected channel.

- It is possible to select 16 channels

5. Synchronisation with a sync cable

Plug the supplied sync cable (Code: MASYG) into the units’ sync terminal

and connect it to your camera. In a multi-ﬂash set-up the sync cable only

needs to be connected to the master-unit, all other slave-units will ﬁre

without delay, triggered by their built-in IR receiver/Slave Cell. Remember

to activate the IR receiver/Slave Cell on each slave-unit.

6. Optical Synchronisation

1. The unit may be ﬁred using an Infrared Remote Trigger (Code: MUSEN,

sold separately). Attach the IR remote trigger to your cameras’ ﬂash

shoe.

The ﬂash units´ IR receiver/Slave Cell must be activated by pressing the

corresponding button. The unit will ﬁre synchronously with the camera

when it is being triggered. In a multi-ﬂash set-up, the IR receiver/Slave

Cell must be activated on each unit.

2. The unit features a built-in “Pre-Flash Eliminator”. It serves the pur-

pose to optically synchronize the unit to a built-in ﬂash of a digital

camera or a shoe mount ﬂash that does not feature a off-function for

the “red eye” or TTL/ETTL pre-ﬂashes. After programming, the unit

“ignores” the cameras´ “red eye” or TTL/ETTL pre-ﬂash pulse and

synchronizes to the main ﬂash of the camera.

- Press and hold the “IR receiver/Slave Cell On-Off” button for approx.

3 sec., the symbol „PF“ (pre-ﬂash) appears on the display, now let go

of the button, a short acoustic signal sounds.

- Now, trigger the camera ﬂash within 10 sec. at a distance of

approx. 2 m from the unit.

- The “IR receiver/Slave Cell On-Off” button blinks steadily, the unit has

“learned” the pulse of the pre-ﬂash, it is now is in pre-ﬂash mode

and syncs to the cameras´ main ﬂash.

To leave pre-ﬂash mode, proceed as described above but without

triggering a camera ﬂash.

The IR receiver/Slave Cell will always be inactive after deactivating

the Pre-Flash Eliminator and must be activated again when required.

7. Radio remote control/ ID selection:

With the radio remote control (TRIGGER HAPPY, sold seperately),

it is possible to control all functions of the PROFILUX PLUS.

Up to 16 ﬂash units and su/jointfilesconvert/344595/bgroups of units can be controlled with one

radio remote control.

Before using a radio remote control it is necessary to select an ID as well

a CHANNEL on each unit.

Use the „Beep/Lamp Ready indicator“ button to select an ID:

- Press and hold the “ Beep/Lamp Ready indicator ” button for approx.

3 sec., the symbol „ID“ appears on the display

- The desired receiving ID can now be set by turning the output control

dial e.g. to “1“ (ID 1).

- Conﬁrm the selection of the ID by pressing the “ Beep/Lamp Ready

indicator“ button, a short acoustic signal sounds.

For detailed information on controlling PROFILUX PLUS ﬂash units with

a radio remote control (TRIGGER HAPPY) please refer to the corresponding

user manual.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 25 26

Commentaires sur ces manuels

Pas de commentaire

Multiblitz Profilux plus 200 Ws Guide de l'utilisateur Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour appareils photo Multiblitz Profilux plus 200 Ws